How To Jump Start A Car In 10 Simple Steps

It’s a terrible feeling to get into your car on a cold winter morning, turn the key, and hear the starter motor creak and fail to start the engine.

This could indicate a dead battery, but if your battery is only flat, a jump start may be all it takes to get it going again.

If you’re not sure whether the problem is caused by the battery, go to Suzuki Fort Motors Pakistan to get it fixed by the experts.

How To Use Jump Leads To Jump Start A Car?

Jump leads are the most popular and successful way to get your automobile started with a dead battery.

What Will You Require?

A completely charged battery in a second car. Avoid using a hybrid or electric vehicle since it may cause damage.

A good pair of jump leads

Safety Steps Before Jump Starting A Car With Jump Leads

It’s critical not to take any chances when jump-starting a vehicle.

Consult your owner’s handbook first, and if you’re still not sure what you’re doing, call your expert for more information.

Check for damage – if either of the batteries or the jump leads appear to be damaged, don’t chance attempting a jump start.

Take off any rings or metal jewelry you’re wearing, and ensure sure nothing metal comes into contact with the battery terminals.

10 Simple Steps To Jump Start A Car

Turn off all electrical systems or gadgets in the car with the dead battery before starting (lights, radio/CD, sat-nav, etc.) and lower the driver’s window if feasible.
Park the charged vehicle as close to the initial vehicle as feasible without allowing the vehicles to contact, ensuring that the jump leads can reach from one battery to the other easily.
Turn off both vehicles’ engines, take the ignition keys, and lift their bonnets (or boot if the battery is in there).
Connect one end of the red jump lead to the flat battery’s positive terminal. A red plastic cover with a plus (+) sign is commonly found on the positive terminal. To gain access to the terminal, pull the lid back.
Connect the other end of the red jump lead to the positive terminal of the second vehicle’s good battery.
Connect one end of the black jump lead to the good battery’s negative terminal.
Connect the other end of the black jump lead to a good earth point on the casualty vehicle, which is normally a solid metal portion of the engine.
Now try to get the initial car to start. If it still won’t start after several attempts, it could be anything more serious than a dead battery. In this case, seek professional assistance.
If it does start, give it around five minutes to run.
Turn off the initial car, detach the negative jump lead, and ensure that the engine starts up normally. The remaining jump leads should be disconnected.

How To Remove The Jump Leads Securely

Shut down both vehicles’ engines.
Disconnect the black jump lead that is linked to the dead battery vehicle.
Disconnect the second vehicle’s other end of the black jump lead.
Unplug the red jump lead from the second vehicle.
Disconnect the other end of the red jump line from the initial vehicle’s battery.

Following the removal of the leads,

Restart the initial vehicle’s engine.

To be fully useable, the battery must be fully recharged, which is best accomplished over several hours using a high-quality battery charger.

In the interim, if possible, drive the vehicle normally for 30 minutes in low traffic areas to try to recharge the battery.

Read Also: QUICK WAYS TO GET RID OF FOGGY WINDSHIELD

Top 9 DIY WAYS TO REMOVE CAR DENT

What Is Power Steering?

How To Use A Portable Battery Pack To Jump Start A Car

If you’re concerned about being stuck with a dead battery and unable to phone for aid or seek assistance, you can get a portable battery pack as a precaution to keep you moving if your battery dies.

These are available at any car store and can be used to jump start a vehicle without the usage of another vehicle.

Before You Begin

It’s critical not to take any chances when jump starting a vehicle. Study your owner’s handbook first, and if you’re not sure you understand what you’re doing, call your expert for more information.

Check for damage – if either of the batteries or the jump leads appear to be damaged, don’t chance attempting a jump start.

Take off any rings or metal jewellery you’re wearing, and ensure sure nothing metal comes into contact with the battery terminals

Using A Portable Battery Pack To Jump Start

Make sure the battery pack is completely charged first.
Locate the vehicle battery, which is normally placed in the engine bay under the hood, but can also be found in the boot of some vehicles. It’ll most likely be concealed by a plastic cover, which you may unclip to reveal the battery and its two connectors.
Attach the positive (red) lead from the battery pack to the battery’s positive (+) terminal. Connect the negative (black) lead to a good earth point on the casualty vehicle, which is normally a solid metal portion of the engine.
Place the battery pack close to the car on the ground; the leads should be long enough to reach the battery. It’s best not to put it on the engine because it can slide off when it begins.
After connecting the battery pack, turn it on and try to start the vehicle as you normally would. If it still won’t start after several attempts, it could be anything more serious than a dead battery. In this case, seek professional assistance.
If the vehicle begins to start, leave it running for about 5 minutes. Turn off the engine, then turn off the battery pack and remove the battery pack’s leads. Restart the engine at this point.
To be fully serviceable, the vehicle’s battery must be fully recharged, which is best accomplished by utilizing a high-quality battery charger for several hours. Meanwhile, if possible, drive the vehicle normally (not in heavy traffic) for around 30 minutes to try to recharge the battery.